How to Connect Klipsch Speakers

There are a few things you need to know in order to connect Klipsch speakers. First, you need to identify the type of speaker wire you have. Second, you need to determine which speaker input jacks on the back of your receiver or amplifier correspond with the left and right channels of your audio source.

Finally, once you have everything connected, you will need to set your receiver or amplifier’s volume levels.

  • Take the speaker wire and connect one end to the positive terminal of the left speaker
  • Connect the other end of the same wire to the positive terminal of the right speaker
  • Repeat step 1 with a new speaker wire, but this time connect it to the negative terminal of the left speaker
  • Connect the other end of this wire to the negative terminal of the right speaker
  • Finally, take another piece of speaker wire and connect it to either the positive or negative terminals of both speakers; this will completethe circuit and allow sound to flow through your Klipsch speakers!

Klipsch Reference Premiere Atmos setup with speaker placement + Yamaha rx-v681+ svs pb12 4K part 2

How Do You Connect Klipsch Speakers to Each Other?

Klipsch speakers are some of the most popular and well-known speakers on the market. But how do you connect Klipsch speakers to each other? The answer is actually quite simple.

All you need is a speaker wire. First, take a look at the back of your Klipsch speaker. You should see two sets of binding posts, one set for the positive (red) terminal and one set for the negative (black) terminal.

If you’re not sure which is which, simply check the labels on the binding posts themselves. Once you’ve identified the terminals, simply use your speaker wire to connect them accordingly. That’s all there is to it!

Connecting Klipsch speakers to each other is a quick and easy process that anyone can do. Just be sure to use the proper gauge speaker wire for best results.

Can You Connect Two Klipsch Speakers?

If you have two Klipsch speakers, you can connect them together to create a surround sound system. The process is relatively simple and only requires a few steps. First, identify the input and output jacks on each speaker.

The input jack will be where you plug in the audio source, while the output jack will be where you plug in the other speaker. Next, use cables to connect the two speakers together. Make sure that the cable is long enough to reach from one speaker to the other without stretching or pulling too tight.

Once the speakers are connected, turn on both speakers and test the connection by playing some music or watching a movie. You should hear sound coming from both speakers equally. If one speaker is louder than the other, adjust the volume levels until they are balanced.

How Do I Set Up Klipsch Wireless Speakers?

If you’re looking to add some wireless speakers to your home theater setup, Klipsch is a great option. Here’s a step-by-step guide to setting up your Klipsch wireless speakers. 1. Start by placing the left and right front speakers in their respective locations.

If you’re using a subwoofer, place it in the front of the room as well. 2. Connect the left and right front speaker wirelessly to the receiver using Klipsch’s Wireless Speaker Adapter (sold separately). 3. Next, connect the subwoofer wirelessly to the receiver using Klipsch’s SWA-8500S Wireless Subwoofer Kit (sold separately).

4. Finally, connect the receiver to your TV or other audio source. Once everything is connected, power on all of your components and adjust the volume levels accordingly.

Why Do My Klipsch Speakers Have 2 Inputs?

If you have ever wondered why your Klipsch speakers have two inputs, wonder no more! We will explain the reasoning behind this design feature and how it can benefit you. As most people are aware, Klipsch is a highly respected name in the audio world.

They have been making high-quality speakers for many years and their products are used by both professionals and amateurs alike. One of the things that sets Klipsch apart from other speaker manufacturers is their use of horn-loaded tweeters. This unique design gives Klipsch speakers a distinct sound that many people love.

Another thing that makes Klipsch speakers stand out is their use of two inputs. Many other speaker brands only offer one input, but Klipsch decided to include two so that users could take advantage of the benefits of both balanced and unbalanced connections. Let’s take a closer look at each type of connection to see why having two inputs can be beneficial.

Balanced Connection: A balanced connection is often used in professional audio applications where noise reduction is important. The three mainconductors in a balanced connection are shielded from interference, which helps to create a clearer signal path between your source component and your speakers. In addition, balanced cables tend to be less susceptible to electromagnetic interference (EMI).

Unbalanced Connection: An unbalanced connection is typically used in home stereo applications and is the more common type of connection between source components and speakers. Unbalanced cables usually have two conductors (a positive and negative) and do not offer the same level of protection against interference as balanced cables. However, they are often cheaper and easier to work with than balanced cables.

How to Connect Klipsch Speakers


How to Connect Klipsch Speakers Bluetooth

Klipsch has been in the audio business for over 70 years, so it’s no surprise that they know a thing or two about Bluetooth speakers. The Klipsch Reference R-15M are one of our favorite pairs of powered monitors, and they can easily be connected to your phone, tablet, or laptop via Bluetooth. Here’s how:

1. Make sure that your Klipsch Reference R-15M speakers are powered on and in Bluetooth pairing mode. To do this, press and hold the “Bluetooth” button on the back of the left speaker for 3 seconds until the LED indicator light begins flashing blue. 2. Open the Bluetooth settings on your device and select “KlipschReferenceR-15M” from the list of available devices.

3. Once paired, you should hear a confirmation tone from your Klipsch speakers and see a solid blue LED indicator light on both speakers. 4. Now simply adjust the volume using either your device’s volume controls or the physical volume knob on each speaker. Enjoy!

How to Connect Klipsch Speakers to Receiver

If you’re looking to add some serious sound to your home theater setup, Klipsch speakers are a great option. But how do you connect them to your receiver? Here’s a step-by-step guide:

1. Start by connecting the left front speaker to the left front channel on your receiver. Do the same for the right front speaker and channel. 2. Next, connect the left surround speaker to the left surround channel on your receiver.

Again, do the same for the right surround speaker. 3. Now it’s time to connect the subwoofer. The subwoofer typically has its own power source, so all you need to do is connect it to an open input on your receiver using an RCA cable.

4. Finally, make sure all of your speakers are powered on and then turn on your receiver. You should now be able to enjoy true 5.1 surround sound!

How to Connect Klipsch Speakers to Computer

If you’re looking to improve your computer’s audio output, one of the best ways to do so is by connecting a set of Klipsch speakers. Known for their high quality and exceptional sound, Klipsch speakers can take your computer’s audio to the next level. Here’s how to connect them:

1. Begin by connecting the left speaker to the left audio output on your computer using an RCA cable. 2. Next, connect the right speaker to the right audio output on your computer using an RCA cable. 3. If you’re using a subwoofer, connect it to the subwoofer output on your computer using an RCA cable.

4. Once everything is connected, power on your speakers and adjust the volume levels to suit your preference. You may also need to adjust the settings in your computer’s sound control panel in order to get the best sound quality possible.


Klipsch is a well-known name in the world of speaker systems, and for good reason. Their products are known for their quality sound reproduction and durability. But if you’re not familiar with Klipsch speakers, you might be wondering how to connect them so that you can enjoy their superior sound quality in your own home.

Luckily, connecting Klipsch speakers is a relatively simple process that anyone can do, as long as they have the right equipment. The first thing you’ll need is an amplifier or receiver that’s compatible with Klipsch speakers. Once you have that, simply connect the amplifier to your speakers using speaker wire, and then plug the power cord into an outlet.

Now it’s time to test out your new setup! Turn on your music player of choice and crank up the volume. You should immediately notice a difference in sound quality compared to using your TV’s built-in speakers or even other external speakers.

Congratulations – you’ve just made your first step towards experiencing true audiophile-quality sound!